pressure molding

Experimental study on casting technology of compacted graphite iron powerful diesel engine cylinder block was carried out on existing cylinder block high pressure molding line. The composition of base iron was 3.6%~ 3.9% C;

在现有汽缸体高压造型生产线上进行大马力柴油机蠕墨铸铁缸体的试验，试验铁液化学成分w为3.6%~3.9%C；

互联网摘选

But fiber volume fraction are raised via elevating molding pressure, when the molding pressure are too high the fibers will be damaged seriously, the composites will become brittler and show poor mechanical properties as a result.

但是纤维体积分数的增加要通过提高模压压力来实现，当模压压力过大时，纤维出现机械损伤，复合材料变脆、力学性能降低。

互联网摘选

transformation of knock-out system of automatic high pressure molding line

高压造型自动线落砂系统的改造

互联网摘选

the matrix formulation and technical properties and processing technology of the low pressure molding compound were studied in this paper.

本文探讨了低压模塑料的配方、性能及加工工艺。

互联网摘选

Fiber Dispersion& Molding Viscosity Control of Low Pressure Molding Compounds

低压片状模塑料纤维分布与模内粘度控制

互联网摘选

Major equipment is vacuum-injection machine, low-pressure injection molding machine, three-dimensional laser scanner camera.

主要销售设备有真空注型机 、 低压注塑机 、 三维激光照相扫描仪.

互联网摘选

Based on the analysis of molding principle about heat pressure tee of diameter equalize, suggested molding technics about diameter equalize.

在分析直径补偿热挤压三通成型机理的基础上，提出了直径补偿的成型工艺。

互联网摘选

The results showed that the thickening effect of combined thickeners which were well suitable for viscosity conditions of low pressure molding and low cost conditions of industrialized production, was better than single thickener.

研究表明，联合增稠剂的增稠效果比单一增稠剂的增稠效果要好，更加符合低压模塑的粘度和工业化生产的低成本要求。

互联网摘选

material is cement, sand, coal dust, high pressure molding , need not sinter. the product with good strength , colourful.

原料由水泥、黄砂、粉煤灰组成，高压成型无需烧结，成品瓦强度高、色彩丰富。

互联网摘选

The injection molding process of thermoset plastics bulk molding composition ( BMC) made of automobile lamp reflector is presented in the paper. Process parameters are settled such as barrel temperature, screw speed, injection pressure, injection velocity and holding time and so on.

介绍了热固性团状模塑料（BMC）注射成型汽车前照灯反射镜的工艺过程，确定了BMC注射成型的料筒温度、螺杆转速、注射压力、注射速度和保压时间等工艺参数。

互联网摘选

study on preparation of sialon bonded sic by pressure molding

干压成型法制备SiC-Sialon复相材料的研究

互联网摘选

The results show that the tensile strength of the UHMWPE fiber strands is greatly decreased when the temperature is higher than 123 ℃, and the ballistic absorption energy is up to the highest value when the molding pressure is about 12.5 MPa.

结果表明，温度超过123℃后拉伸强度有大幅的下降，而成型压力为12.5MPa时达到最大值。

互联网摘选

Diameter Equalize Molding of Heat Pressure Tee

直径补偿热挤压三通的成型

互联网摘选

technical transformation of pneumatic micro-jolt high pressure molding machine

对自制双工位气动微震高压造型机的技术改造

互联网摘选

Advanced cast methods used domestically and abroad in famous automobile manufacturers and foundries for cylinder castings of which technical performance has been presented include air impact molding, static pressure molding, vertical parting flaskless molding machine and full mold casting, etc.

介绍了汽缸体铸件的技术性能、国内外各大汽车公司和汽车铸造厂所采用的先进铸造方法，这些方法有气冲造型、静压造型、垂直分型无箱射压造型、实型铸造等。

互联网摘选